Airfoil Control Damper Supplier in NC and SC

At Mike Moore Sales, we offer two different types of airfoil control dampers for your next project in the Southeast US:

Series 1000 – Low Leakage Air-Foil Control Damper

• This damper’s all-aluminum construction provides a prolonged and rust-free operational life.
• Aluminum extrusions allow for intricate design features not possible with roll or brake formed galvanized steel.
• Series 1000 dampers are assembled using slip-proof linkage components that keep blades aligned as per factory adjustment.
• These dampers are supplied with extremely flexible silicone side seals and EPDM blade seals, that are resistant to weathering, compression set, and heat.
• TAMCO seals provide outstanding dynamic fatigue resistance, ensuring consistent minimal leakage rate performance and sealing longevity.
• TAMCO’s dual bearing system is self-sealing, self-lubricating, and non-absorbent, resulting in totally maintenance-free performance.
• Standard blade depth is 6” (152 mm).Caution: Never use any lubricants, such as grease or silicone on TAMCO dampers.

When Should you use the Series 1000 for your project?

• If you are looking for modulating, or 2 position control dampers.
• Where maintenance is an issue.
• If you’re looking for an ideal and reasonably priced choice for replacing worn out common dampers.

Project Downloads

• Series 1000 Performance and Submittal Data
• Series 1000 Suggested Specifications
• TAMCO Aluminum Control Damper Schedule

Series 1500 – Ultra-Low Leakage, Enhanced Air-Foil Control Damper

• The Series 1500 damper utilizes smooth aluminum end caps installed on the hollow air-foil blades.
• This improves sealing where damper blades meet the side frames and reduces leakage rates significantly.
• The unbroken surface of the end caps creates nearly frictionless wear on the frame seals. This enhances damper longevity and ensures that the damper retains consistent sealing ability over time.
• Silicone seals are provided as standard to ensure tight sealing in both cold or warm climates.
• Series 1500 ultra-low leakage dampers are constructed with all of the maintenance-free bearing and linkage components of other quality TAMCO products.
• Standard blade depth is 6″ (152 mm).

When Should you use the Series 1500 for your project?

• When the damper is closed and a low air leakage rate is critical.
• Where infiltration is a concern.
• Where condensation and freeze up are not a concern, but where an energy efficient, low infiltration, maintenance-free damper is essential.
• If you need an ideal specification choice for outside wall dampers intended for use in warmer climates, where energy efficient, non-insulated dampers are required.

Project Downloads

• Series 1500 Performance and Submittal Data
• Series 1500 Suggested Specifications
• TAMCO Aluminum Control Damper Schedule

What Options are available with the dampers?

ET – Elevated Temperature Option:

• Blade and frame seals are extruded silicone, ensuring minimal change in leakage rates as temperature increases, making this damper ideal for high temperature applications.
• Dampers are designed for operation in temperatures as high as 300°F (149°C).
• Bronze-oilite bearings replace Celcon and polycarbonate bearings.

MR – Moisture Resistance Option:

• All zinc-plated steel hardware is replaced with stainless steel, protecting hardware from rust and corrosion when exposed to high humidity or high moisture environments.

SW – Salt Water Resistance Option:

• Extruded aluminum frames, blades and hardware are clear anodized to a depth of 0.7 mil. (18 microns). This prevents rusting and pitting when dampers are exposed to salt spray or high humidity environments.
• Blade and frame seals are extruded silicone, for reduced air leakage.
• All zinc-plated, steel hardware is replaced wtih stainless steel, protecting hardware from rust and corrosion.
• All aluminum linkage hardware parts are clear anodized.